Showing results: 346 - 360 of 2617 items found.
-
MCE -
PdMA Corporation
The MCE? (Motor Circuit Evaluator) is a comprehensive static motor tester that produces detailed analyses of motor and circuit conditions in as little as three minutes. Analysis of the motor and associated circuits through MCE? testing allows for the detection of electrical faults in any one of the five fault zones.
-
Composite Family -
Test Electronics
High Strength, high temperature, semiconductive composite board designed for use as circuit board and flex circuit carrying pallets for solder reflow ovens.
-
CLM1 -
NG Systems Ltd
The Cable Length Meter CLM1 will allow the accurate measurement of severed or open/short-circuit CCTV coaxial cable. For use with RG59 (75Ω) and RG58 (50Ω) or equivalent coaxial cable, this meter provides a direct readout in metres of the length of an unterminated run of coaxial cable with a resolution of 2-3 metres. A single range of 2.5 to 400 metres on a 4 digit LCD display is provided with automatic indication of open circuit and short circuit conductors. By this means, the location of a short circuit or open circuit in cable runs of up to 800 metres may be found.
-
11930B -
Keysight Technologies
The Keysight 11930B limiter provides input protection for a variety of RF and microwave instrumentation. Failure mode for the limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage. The Keysight 11930B provides the same protection to spectrum analyzers and sources. At even greater power levels, failure mode for limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage.
-
Seaward Electronic Ltd
High voltage phasing rods enable phase comparisons to be made at the point of paralleling two circuits without the interposition of voltage transformers or secondary wiring circuits.
-
ifm efector, inc.
*Space-saving design*High power reserves*Low heating of the control cabinet*Low inrush current*Safe switch-off by circuit breakers in case of short circuit
-
FB315 -
Matco Tools
*Tests circuit current from 0 to 80A*Includes 20A maxi fuse for use with mini and ATC circuit testing*Resolution: .1A (100 mA)
-
Extech ET10 -
Extech Instruments Corporation
The Extech ET10 is a GFCI Receptacle Tester. It tests GFCI circuits for faulty wiring in 3-wire receptacles. Lights indicate circuit condition. It comes with a 3-prong plug.
-
-
Hanwa Electronic Ind. Co.,Ltd.
◆Adaptable to the following international standard waveform;JEDEC, ESDA, AEC, and JEITA◆This system’s uniquely short discharge circuit is made possible by its original mechanical design.◆The short circuit minimizes the influence of inductance and capacitance on the data.◆The use of a single circuit ensures data stability for each device pin tested.
-
-
26330 -
Lisle Corp.
If the bulb lights up, continuity exists. If the bulb fails to light, the circuit is open. Not for use on live circuits, but incidental contact with 12V supply will not burn out LED bulb.
-
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA Cable Continuity Detector can test the open circuit, short circuit, crossover and continutiy for RJ11/RJ45/BNC/USB cable, and the test result is displayed by the visible LED light status.
-
#TFT100 -
NSI Industries
Stop guessing about circuit breaker tripping issues. See why, when and where a circuit breaker trips. For the first time, you can detect the type of fault, and locate the position of an electrical “event” that causes intermittent and persistent circuit breaker trips, and No Fault Found (NFF) conditions. The critical information needed to reduce […]
-
Pro-Check 725 -
LITE-CHECK LLC.
Pro-Check trailer light testers with advanced electrical diagnostics are rugged, lightweight, and economical. They independently test each electrical circuit on a trailer to ensure proper connectivity. The Pro-Check identifies each specific type of electrical wiring fault. Lite-Check’s patented active diagnostic system takes the guesswork out of identifying trailer light and electrical problems. The Pro-Check commercial trailer light tester with electrical circuit diagnostics, not only identifies faults, but the specific circuit the fault is on. Faults are identified as “Open Circuit”, “Open Ground”, “Short” (w/all circuits identified), or “Chassis Ground”. Audible alarms alert technicians to found electrical faults.